Lenticular Studio

Calibrate your lens with the Pitch Test, build a lenticular flip template, and print sharp prints that change when tilted.

18 min read Updated 8 Nov 2026 Watch the video (7:58)

Lenticular Studio turns two or more photos into one interlaced print. Put a lenticular lens sheet on top, tilt it, and the picture flips between the photos. The lens has to match the print exactly, so start with the Pitch Test, then build your template.

How a lenticular print works

A lenticular lens sheet is a clear plastic sheet covered in tiny parallel ridges (lenses). Q-Booth slices each of your photos into very thin strips and weaves the strips together on one sheet. Each ridge sits over one strip from every photo. When you tilt the card, each ridge shows a different strip, so you see a different photo.

This only works if the strips line up with the ridges. The number that controls this is the LPI (lenses per inch). If it is off by even a few hundredths, the print looks blurry, striped or "ghosted" (both photos visible at the same time).

Note

On screen the interlaced result looks like a mess of fine stripes. That is normal. Only the lens on top turns it back into clean photos.

What you need

  • A lenticular lens sheet. The box shows an LPI value, for example 50 or 75. Treat it as a starting point, not the final answer.
  • A photo printer and glossy photo paper.
  • Tape or adhesive to fix the lens to the print, and a cutter to trim it.
Note

Lenticular is an add-on, included in Pro. On Basic and Advanced the studio still opens and works, but without the Lenticular add-on the results carry the demo watermark. See the Products page. Lenticular is not available in Easy mode: use Expert mode.

Step 1: the Pitch Test (do this before printing)

The Pitch Test prints a calibration sheet with many bands, each made for a slightly different LPI. You lay the lens on the sheet and find the one band that looks right. Its number is the correct LPI for your printer, paper and lens together.

Important

The Pitch Test result belongs to one combination of printer, paper and lens. Repeat it whenever you change any of them, including a new batch of lens sheets.

Open the Pitch Test

  1. Open Studio › Lenticular.
  2. In the left panel, under the Template section, find the Pitch Test row. It is always visible, not hidden in a menu.
  3. Click Open Pitch Test…. The Pitch Test Calibration window opens, with LPI, DPI and Direction already filled in from the template's Lens tab. Changing them in the pitch test does not change the template.
Pitch Test Calibration window with Band Settings on the left and Printer Settings on the right
The Pitch Test window: describe the test sheet on the left, set up the printer on the right.

Set the bands

  1. LPI: type the number from the lens box, for example 50.
  2. DPI: the print resolution, for example 600 or 720. Write it down. You must use the same DPI in every test and later in the template.
  3. Direction: choose Vertical if the ridges on your lens run top to bottom, Horizontal if they run left to right. It must match the physical lens.
  4. Step Size: how far apart the bands are. Use 0.05 for the first pass.
  5. Range: how far above and below your LPI to test. Use 0.5 for the first pass. With LPI 50 this gives 21 bands from 49.50 to 50.50.
  6. Leave Maximize accuracy (fit to page) on. It makes the bands as large as the page allows, and bigger bands are easier to judge. Turn it off only if you need a specific Width (in) and Height (in).

The bar at the bottom right shows Total Bands and Estimated Pages and updates as you type.

Set up the printer

  1. Choose the Printer, Paper Size and Orientation.
  2. Click Printer Properties or Preferences to open the Windows printer driver and follow the Printer Tips card: highest quality, photo/glossy media, borderless off and bidirectional printing off.
  3. In any print dialog, print at actual size (100%). Never use "fit to page".
  4. Click Print Pitch Test. If the printer is on another computer, click Save as PNG (one file per page, named _Page1, _Page2… when there is more than one) and print that file there, also at 100%.
Tip

Bidirectional printing prints alternate passes in opposite directions. On a sheet of very fine lines that alone can ruin the test, so always switch it off.

Read the sheet

Printed pitch test sheet with labelled bands 49.50, 49.55, 49.60 and so on
Part of a printed test sheet. Each band is labelled with the LPI it was made for.
  1. Lay the lens on the printed sheet, ridges parallel to the band lines.
  2. Look from the distance your guests will hold the finished print.
  3. Tilt your head left and right (Vertical) or up and down (Horizontal).
  4. Most bands break up into zebra stripes: those numbers are wrong. Find the one band that switches from solid black to solid white all at once.
  5. Read the number printed above that band. That is your LPI.

Optional: a finer second pass

For extra precision, run the test again centred on the number you found (for example 50.15) with Step Size 0.01 and Range 0.05. That prints 11 bands one hundredth apart. Do not go finer: the band labels show only two decimals.

Write the result down

Close the Pitch Test window. It does not fill in the template for you: go to the Lens tab and type the LPI you found, plus the same DPI you tested at. Write down both numbers, because they only work as a pair, and only for that lens batch on that printer with that paper.

Step 2: the Lens tab

The Lens tab describes the physical lens and the size of the finished print.

Lenticular Studio Lens tab with Direction, LPI, DPI, Lens W, Lens H and Enable Separator
Lens tab filled in for a 6 × 4 inch print.
SettingWhat to enter
DirectionVertical or Horizontal, exactly as in the Pitch Test.
LPIThe value you found with the Pitch Test (for example 50.15), not the number on the box. New templates start at 40.
DPIThe same DPI you used in the Pitch Test. New templates start at 600.
Lens W (inch) / Lens H (inch)The physical size of the finished piece in inches, for example 6 × 4. New templates start at 4 × 6.
Enable Separator (Reduce Ghosting)Adds a narrow buffer between the images so one does not bleed through the other mid-flip. On by default for new templates; leave it on for image flips.

The finished sheet is Lens W × DPI by Lens H × DPI pixels: 4 × 6 inches at 600 DPI is 2400 × 3600. That is a very large file, which is expected.

Step 3: the Images tab

Each row in the Images tab is one image in the flip. A new template starts with no layers, and you need at least two; Q-Booth will not save or process with fewer. The order of the rows is the order the images appear as the card is tilted. Each extra picture gets a thinner slice under each ridge, so two pictures give the cleanest flip.

Every layer fills the whole lens area (to put the pictures inside a frame's window, see Custom Frame). There is no canvas to drag layers on and no Edit button: everything about a layer is set in the panel below the list.

Images tab with two Plain Photo layers; the layer settings end with Source Image and Result, with no Custom Frame section
Two Plain Photo layers. A new layer has no Custom Frame section (since 5.9.6.1).
  1. Open the Images tab and click + (Add Layer) under the table. It adds a Plain Photo layer named image_1, image_2…
  2. Click the name and give it a clear name, for example "Pose A". Layer names are shown to you (and the guest) when the photos are asked for.
  3. Under Image Settings, choose the Type (see below).
  4. Set Size Mode to Crop (fills the whole area, trims the edges) or Fit (keeps the whole photo; the empty edges are filled with black). New layers start on Fit. For a flip, use Crop on every layer so the images line up with no black bars.
  5. Fill in the Content and Source Image sections. Input Image = Independent uses a fresh photo from the camera.
  6. Add the second layer the same way. Drag rows or use the up/down arrows to change the order, the copy icon to clone a layer (named …_Copy) and the bin icon (or the Delete key) to remove one. Removing asks no confirmation.
TypeUse it for
Plain PhotoThe photo as it is, with no AI. Content: Aspect Ratio (Free keeps the camera's own shape), Background (Original / Remove BG / Change BG) and Face Restoration.
Studio TemplateRuns a saved studio template (Photo Studio, AI Online or AI Offline) inside the layer. AI Online and AI Offline are hidden on a Basic license. Use an AI Online template that makes a still image; a video model makes no sense in a lenticular layer. Since 5.9.6.0 this is enforced: the AI Online window opened from a layer greys out Video output and Turn into video, Save & Return and Open refuse a video template, and Save / Process refuse an older layer that still holds one ("Lenticular Studio needs a picture, but this template makes a video").
FaceswapA guest photo with the face swapped onto a scene picture you choose (Advanced or Pro license; it isn't in the list otherwise). To also hand out the face-swap photo on its own, use Include as result.
Image FileA fixed picture you provide, the same on every print (for example a logo card or a "reveal" image). It never needs a photo.

There are no text, QR Code or Layer Result layers in Lenticular.

Use one photo for several layers (chaining)

Plain Photo, Studio Template and Faceswap layers have a Source Image section. Its Input Image is:

  • Independent: the layer gets its own new photo.
  • From another layer Input: reuses the raw photo of the layer you pick in Layer.
  • From another layer Result: uses the finished picture of the layer you pick.

An Independent layer has no photo picker in the editor: its photo is asked for when you press Process, or taken by the guest at an event. A chain must start at an Independent layer or an Image File layer. Deleting a layer does not fix the layers that used it, so re-point them before you save.

Example: a real photo that flips into the AI version.

  1. Layer 1: Plain Photo, Independent, Size Mode › Crop.
  2. Layer 2: Studio Template › AI Online with an AI template, Size Mode › Crop.
  3. On layer 2, set Source Image › Input Image to From another layer Input and Layer to layer 1.

Process now asks for one photo. Layer 1 shows the real photo, layer 2 the AI version of the same photo, and the card flips between them.

Custom Frame

Note

Replaced in 5.9.6.1. To put the pictures in a frame now, set Overlay to Custom with the frame and turn on Put the photo inside the frame's window: every layer goes inside the frame's window (see Put the photo inside a frame). Design the frame at the lens shape. The Custom Frame section is gone for new layers. It only shows on a layer that already uses one (older templates keep working), and switching it off there hides it for good. The rest of this section describes the old Custom Frame, for older templates.

Under Custom Frame (collapsed by default), Use Custom Frame shows a layer's picture inside a smaller box on a lens-sized background, with an optional decoration image. Useful when one side of the flip should show the photo inside a branded frame. The frame is only used when the switch is on and a frame box has been made.

  • Create Frame... opens the Layer Frame Editor with a small box in the middle to start from. Once a frame exists, the section shows a preview, and the buttons become Edit Frame... and a bin icon (Clear Frame, which asks first and also switches Use Custom Frame off).
  • Overlay inside frame: on, the template overlay goes on the photo inside the box only; off, it covers the whole lens area.

In the Layer Frame Editor:

  • Drag, resize and rotate the box on the lens area, with handles on every side as well as the corners. A head-and-shoulders outline shows where a typical subject sits.
  • Frame Image: the decoration picture, fitted to the lens area. Empty means Blank Canvas (a white background).
  • Image Position: Above Frame (the photo is drawn on top of the frame image) or Below Frame (the frame image is on top; use a PNG with a transparent hole where the photo should show).
  • Geometry: exact position, size and rotation. When the layer has a fixed aspect ratio, the box keeps that shape.
  • Cancel discards your changes; Save & Return keeps them.

Include a layer as its own result

Open the Result section of a layer and turn on Include as result to also deliver that layer's finished photo as a separate result, next to the lenticular sheet. When it's on, an Overlay choice appears for that separate photo: Disabled (the starting value), Default (the template's overlay) or Custom (pick an image).

Important

The lenticular sheet itself is never shared by QR or email. The only things guests can receive are the layer photos you mark Include as result and the slideshow video. If neither is on, there is nothing for the guest to download.

Overlay and slideshow video

  • Overlay (left panel): Disabled, Default (the overlay from Settings, or the event's overlay inside an event) or Custom. The overlay is applied to each layer before interlacing, so it is sliced by the lens pattern like the photos and shows whichever way the card is tilted. With Custom, the Put the photo inside the frame's window switch (since 5.9.6.1) puts every layer inside the frame's window (see Custom Frame). The Slideshow Video overlay and a layer's Include as result overlay have the same switch.
  • There is no QR Overlay section and no QR Code layer: a QR code on a sheet cut into thin slices could never scan.
  • Camera Filter (Use Global / Off / Custom) is the colour filter for photos taken with this template; it only applies to camera shots, not to files picked from disk. Under it, Beauty Filter (since 5.9.0.0) has the same three choices. Both are used when the template runs in an event; the camera inside Lenticular Studio itself uses the app-wide Camera Filter and Beauty Filter.
  • Options › Slideshow Video: turn on Generate slide video to create a short MP4 that cycles through the layers' pictures, in layer order. Set Duration per image (s) (0.5–10, default 1), Loops (1–10) and an optional Overlay image (optional), which is stretched to the frame and baked onto every frame (the frames already carry the template overlay, so use it only for something video-specific). This video is what guests can share; the lenticular sheet only works in the hand.
Options section with Generate slide video switched on
Options › Slideshow Video.

Step 4: save, process and print

  1. Click Save. Tip: put the LPI in the file name (for example flip_6x4_50.15.qsl) so you know which lens it was built for.
  2. Click Process (F5). If any layer is Independent, the Lenticular Studio Input window appears first with one card per layer: click Select Image on each (camera, clipboard, gallery or file), then Run Template. This is the same screen guests see at an event. If a layer's AI template has guest questions, a prompt window opens for each. Q-Booth renders each layer at full print resolution and interlaces them; this can take a while and uses a lot of memory at high DPI.
  3. Check the result on the right. Use the arrows to move between the lenticular sheet (a large PNG, always first), the slideshow video (if on) and each layer marked Include as result. The Compare tab puts one layer's picture beside the sheet with a slider.
  4. Click Share, then Print. Adjust Photo is disabled for the lenticular sheet (the layer photos can still be adjusted). The sheet prints at true size (1:1), at exactly Lens W × Lens H inches in the top-left corner of the printable area. It is never fitted to the page, centred or rotated, so use paper at least as big as the lens, oriented the same way (portrait for 4 × 6, landscape for 6 × 4). This also applies when printing from the Gallery (since 5.5.1.0) and at events.
  5. Lay the lens on the print and slide it until the image snaps into place. Tape it down and trim.
  6. When you are happy, click Save & Return (inside an event) or Save.
Share Result window showing the striped lenticular sheet and the slideshow video
The interlaced sheet and the slideshow video in the Share window.
Important

Never let anything scale a lenticular print: no "fit to page", no resizing, no cropping. A resized sheet no longer matches the lens.

Note

The lenticular sheet is never shared or uploaded (since 5.5.2.0): on the sheet the QR and email buttons hide, and they come back when you move to a layer photo or the video. A smaller copy of each layer is kept as an "extra" (in the Gallery it shows in the Extras strip), but those copies are not uploaded either. Only the Include as result photos and the slideshow video go online.

Use the same printer, paper and DPI you ran the pitch test with, and the same printer settings (highest quality, photo/glossy media, borderless off, bidirectional off). Reset clears the whole template, including the layers.

Using it at an event

  • Add a lenticular template to an event like any other, including Create in Studio in the event's template list (build it, then press Save & Return). See Templates.
  • The number of photos the guest takes is the number of Independent layers. A two-photo flip takes two shots; a "real → AI" flip chained from one layer takes one. Lenticular only takes still photos (no video or behind-the-scenes clip).
  • Guest questions from AI templates inside the layers are asked on the Input page, labelled with the layer name (since 5.5.5.3).
  • On the Result page the sheet is shown and can be printed (always at true size), but not shared. Guests share the Include as result photos and the slideshow video.
  • A lenticular template can't be a target of Switch Template on the Result page, and Automation Studio doesn't run lenticular templates.

Three things to remember

  1. LPI and DPI travel together. The LPI you found only works at the DPI you found it with.
  2. Direction on the Lens tab must match the direction you tested.
  3. Always print at 100%.

Troubleshooting

The print is blurry or shows broad stripes when tilted.

The LPI does not match. Run the Pitch Test with the same printer, paper and lens, enter the new LPI on the Lens tab, and check that the DPI is the one you tested with.

I see both images at the same time (ghosting).

Turn on Enable Separator (Reduce Ghosting), check that Direction matches the ridges, and slide the lens sideways until it registers. Then check the LPI again.

It worked before, but not with new lens sheets or paper.

The calibration only fits one printer + paper + lens combination. Repeat the Pitch Test.

The print does not fit the lens size.

Something scaled it. Print at actual size / 100%, with borderless printing off, and check Lens W (inch) and Lens H (inch).

"At least 2 layers are required."

Add a second layer on the Images tab before processing.

No band looks clean on the test sheet.

Check the printer settings first (bidirectional off, highest quality, photo paper, 100%), and that Direction matches the lens. If the right value is outside the tested range, increase Range and print again.

I ran the pitch test but nothing changed.

The result isn't copied automatically. Type it into Lens › LPI, with the same DPI.

There are black bars on the pictures.

The layer's Size Mode is Fit and the photo's shape doesn't match the lens size. Switch to Crop.

Guests get no QR or nothing to download.

The sheet is never shared. Turn on Include as result on the layers and/or Generate slide video.

There is a demo watermark on the results.

The license doesn't own the Lenticular add-on (included in Pro).

Error messages

MessageWhat to do
At least 2 layers are required.Add a second layer.
Please select image for all required layers.Every card in the input window needs a photo.
Please attach an image for the image-type layer.Pick a picture for the Image File layer, or change its type.
Layer ID … not foundA layer points at a layer that was deleted. Re-pick its Layer under Source Image, or set it to Independent.
Circular dependency detected at layer …Two layers use each other. One must be Independent (or an Image File).
Chain ends at layer … which is not type of Static Image or Independent InputThe chain must start at an Independent layer or an Image File layer.
Layer … is Independent input image, cannot chain to other layersRe-select the layer's Input Image and set it again; if it should be Independent, leave it Independent.
…could not be processed (input image missing or upstream chain incomplete)A layer's photo is missing. Check that every Independent layer got a photo and every chained layer points at a valid layer.

Next steps

Still need help?

Our team answers on WhatsApp. Tell us your Q-Booth version and what you see on screen.

Chat on WhatsApp