Flipbook Studio

Turn a short video into printed flipbook pages, then cut, stack and bind them into a book guests can flip.

13 min read Updated 8 Nov 2026 Watch the video (5:00)

Flipbook Studio turns a few seconds of video into printed pages. Cut them, stack them, clip them together, and guests have a little book they can flip again and again. This page covers the template settings, the video source, the cover, processing, and the physical cutting and binding.

Before you start

  • A photo printer and paper, for example 4 × 6 inch.
  • A paper cutter. A guillotine cutter gives the cleanest, most even edges.
  • A binder clip, a stapler or a strip of tape.
  • A camera set up in Settings › Camera if guests record at the booth.

Open Studio › Flipbook. Templates and overlay are on the left, the Settings, Content and Cover Image tabs are in the middle, and a live preview of the printed page is on the right.

Note

Flipbook is an add-on studio, included in Pro. On Basic or Advanced without the Flipbook add-on, the studio still opens with a DEMO badge and the results (video and sheets) get a demo watermark. See the Products page. Flipbook is not available in Easy mode: use Expert mode to make one.

How the page count works

Q-Booth takes frames from the video at the Frame Per Second rate and places them on pages in a grid (Composition). So:

  • Frames = video length (seconds) × frames per second.
  • Pages = (frames + cover, if any) ÷ frames per page, rounded up.

Example: 5 seconds × 5 fps = 25 frames. Add a cover = 26 cells. With 3 frames per page that is 9 pages. At 10 fps it becomes 50 frames and 17 pages. The Content tab always shows the current estimate, for example Estimated Pages: 9 (25 frames @ 5fps).

Tip

More frames give smoother motion, but a thicker book and more cutting. For most events, 5 seconds at 5 fps is a good balance.

Settings tab

Flipbook Studio Settings tab: paper 4 x 6, composition 3 x 1, 5 frames per second, binder Left 30, Image Size Crop
Settings used in this example: 4 × 6 paper, 3 rows × 1 column, 5 fps, binder Left 30 px, Crop.
SettingWhat it doesDefault
Paper Size (inch)Width × height of the sheet you print on, 1–20 inch.4 × 6
CompositionRows × columns: how many frames fit on one sheet. 3 × 1 on 4 × 6 paper gives three wide frames of about 4 × 2 inch each, a classic flipbook size.3 × 2 (6 frames)
Frame Per SecondHow many frames are taken from each second of video, 1–60. This decides the page count.5
Binder (Pixel)The binding side (Left, Right, Top, Bottom or None) and the width of the strip left there for the clip (0–200 px). Each strip carries the frame number, which keeps your pages in order later. With None (or width 0) there is no strip and no frame numbers, so stacking in order is much harder.Left, 30
Line Color (Pixel)The colour and thickness (0–50) of the lines drawn between frames. These are your cut lines; keep them thin and dark so they disappear in the cut. 0 means no lines.Black, 3
Image SizeCrop fills each frame edge to edge; Fit keeps the whole picture and can leave white bands. Use Crop for flipbooks so nothing jumps around (the default is Fit, so change it).Fit
Image OrderLeft-Right or Top-Bottom: the order frames are placed in the rows × columns grid. Only matters with more than one column.Left-Right

The sheets come out as JPG pictures at good print quality (about 2000 pixels on the short side).

Important

The binder side must match the side you will actually clip. If you choose Left but bind at the top, the empty strip is on the wrong side and the clip covers the picture.

Content tab: where the frames come from

Choose one of two sources at the top of the Content tab.

Video Recorder

Films the guest right at the booth.

Content tab with Video Recorder selected, 16:9 aspect ratio, 5 second duration and the estimated page count
Video Recorder: 16:9, 5 seconds, Normal, 1x. The estimate is shown underneath.
SettingWhat it doesDefault
Aspect RatioShape of the recording: Original (the camera's own shape) or a fixed shape such as 16:9, 9:16, 1:1, 2:3, 3:2, 3:4 or 4:3. 16:9 matches the wide 3 × 1 frames.Original
Record Duration (Seconds)How long the camera records, 1–120 seconds. Five seconds is plenty; a flipbook is one small moment.5
Playback ModeNormal, Reverse or Boomerang (forward, then back). Boomerang doubles the frames, so twice the pages.Normal
Playback Speed0.5x, 1x, 1.5x or 2x. Speed changes the frame count too: 0.5x makes the clip twice as long (twice the pages), 2x halves it.1x

The recording has no sound.

Studio Template

Takes the video from another studio instead of the camera. Choose the Studio Type (Motion Studio or AI Online), then Create New (opens that studio in a window; press Save & Return when done) or Open › From Gallery... / Browse File.... Once loaded: Edit, Replace, Clear. Switching Studio Type discards the current template (it asks first).

An AI Online template must make a video: a video model, or a picture model with a video step (Turn into video; Video Chain on 5.9.5.0 and older). This lets a guest take one photo, have AI bring it to life, and receive it as a flipbook. AI Online isn't offered on a Basic license. Photo Studio and AI Offline templates can't be used here, because they don't make video.

Since 5.9.6.0, an AI Online template that only makes a picture is stopped before it reaches Flipbook: Open refuses it, and in the AI Online window Save & Return refuses it ("Flipbook Studio needs a video, but this template makes a picture"). Pick a video model, or press Turn into video.

Content tab with Studio Template selected and the Studio Type list showing Motion Studio and AI Online
Studio Template as the source.
  • Max Video Length limits how much of the template's video is used (frames are taken from the start): Full length, or 3, 5, 8, 10, 15, 20 or 30 s. New templates start on 5 s, so a long AI video can't turn into hundreds of pages. Older templates, saved before this setting existed, open on Full length and keep working as before.
  • The page estimate depends on the source. With AI Online the video length is known, so it shows the real Estimated Pages: …. With Motion Studio the length is only known after it runs, so it shows Up to … pages based on Max Video Length, or For 5 seconds video will need … pages when it is set to Full length.

Cover image and overlay

  1. Open the Cover Image tab and switch on Use cover image.
  2. Click Select image and pick the picture from the clipboard, the gallery or a file (the camera is not available for the cover).
  3. The cover takes the first cell of the first page, without a binder strip. It counts as one frame in the page estimate, and the picture is saved inside the template.
Cover Image tab with Use cover image on and a cover design shown in the first cell of the preview
The cover appears in the first cell of page 1.
Important

You can pick a cover image even while Use cover image is off, but then it is not used. Always check the switch.

Don't confuse this with the Cover image in the left panel's Event section: that one is the thumbnail guests see in the event's template picker, and it doesn't go into the flipbook.

Overlay in the left panel has three choices. New templates start on Disabled.

  • Custom: pick a PNG with Select overlay image. It is laid over every frame on the sheets and over the video, which suits an event logo or date on each page. The overlay is stretched to the shape of one frame (not the whole sheet), so design it at the frame's shape. Since 5.9.6.1, the Put the photo inside the frame's window switch puts the picture inside the frame's window instead, on every sheet frame and in the video (see Put the photo inside a frame).
  • Default: uses the global overlay from Settings (or the event's own overlay, inside an event). In the current version it goes on the video only, not on the printed frames. To brand every frame, use Custom.
  • Apply overlay for cover page also puts the overlay on the cover. It is off by default, so the cover stays clean.

Flipbook has no QR Overlay section: a QR code is never printed on the sheets. Guests get the video through the QR on the result screen or in Share.

Camera Filter (Use Global / Off / Custom) is the colour filter for footage captured with this template; it only applies to camera captures, not to files picked from disk. Under it, Beauty Filter (since 5.9.0.0) has the same three choices. Both are used when the template runs in an event; the camera inside Flipbook Studio itself uses the app-wide Camera Filter and Beauty Filter.

Save, process and check the result

  1. Use the Preview / Result switch above the canvas. Preview shows one sample page that updates as you change settings.
  2. Click Save. Flipbook templates are saved as .qsf files. At an event, this file is all you need.
  3. Click Process (F5). If the source template has dynamic prompt questions, they are asked first. The Flipbook Studio Input window then asks for the input: a video for Video Recorder (Select Video: open a video, record with the camera, the gallery or a recent file), a photo for AI Online (Select Image), or Motion's own input window for a Motion template. Press Run Template; the rest is automatic.
  4. The Result view shows two things: the video first (guests download it with the QR code), then the pages, cover first. Use the arrows at the top right to flip through them (the counter shows, for example, 1 / 10: the video plus 9 sheets).

The video goes in the result folder and shows in the Gallery. The sheets are kept with it and appear in the Gallery's Extra strip when you select the video; they are not uploaded to the QR/cloud.

Result view showing page 1 with the cover and the first two frames
Result view: page 1 with the cover and frames 1 and 2.

Print the pages

  1. Click Share, then Print. The Print Image window opens, listing every sheet, all ticked.
  2. Press Print Selected to print them all in one go, in order, on the paper size you set (for example 4 × 6). Deselect All / Select All toggles every sheet, so you can tick only the ones you want.

When several printers are enabled, a Printer choice appears (Auto (least busy) or a specific printer). The whole book always goes to one printer, so the pages come off the same stack. There is no copies or orientation choice: each sheet is fitted to the page.

Reprint one bad sheet from the Gallery

Since 5.5.5.3, when a sheet jams or prints badly you don't need to print the whole book again:

  1. Open Gallery and select the flipbook's video (or one of its sheets in the Extra strip).
  2. Press Share (or double-click it), then Print. The Print Image window lists every sheet of that book.
  3. Deselect All, tick only the bad sheet, then Print Selected.

This works in the Gallery inside an event too.

A printed flipbook page with three frames, the binder strip with frame numbers 3, 4 and 5 on the left, and black cut lines
One printed page: three frames, numbered binder strip on the left, cut lines between frames.

Cut, stack and bind

  1. Cut along the lines. A guillotine keeps every frame exactly the same size, which is what makes the book flip smoothly.
  2. Stack the frames by the numbers on the binder strip: frame 1 on top (after the cover), all strips on the same side.
  3. Square the stack by tapping it on the table.
  4. Bind the binder edge with a binder clip, two staples or a strip of tape.
  5. Flip: hold the binder edge and let the pages run off your thumb from the other edge.

Using it at an event

Add the saved template to an event (see Templates), or make one straight from the event's template list with Create in Studio. Guests record at the booth, the pages are printed, and the video is shared by QR. Printing and sharing are set up per event in Sharing & printing.

  • One capture per guest. With Video Recorder the camera records for the Record Duration; with an AI Online source the guest takes one photo and the AI turns it into the video.
  • Prompt questions from an AI Online source appear on the event's Input page (since 5.5.5.3).
  • The result screen shows the video first, then the sheets.
  • One tap on Print prints the whole book: every sheet, in order, on one printer. There is no copies dialog; a guest who wants a second book taps Print again. Auto print also prints the whole book. (Before 5.5.5.3 a flipbook could not be printed during an event, so update.)
  • Print counters and limits count sheets. A 9-sheet book counts as 9 prints. The limit is checked before printing starts, so a book that crosses the limit still finishes, and the next print is then blocked.
  • If the event has a print archive folder, every sheet is copied there, so you can reprint a jammed page from it.
  • The QR gives the guest the video. The sheets are never uploaded.
  • An overlay on Default follows the event's own overlay (on the video only, see above).
  • The page count comes from the template (Frame Per Second, Record Duration, Composition), not from the event.
Important

A flipbook whose source is a Motion Studio template isn't supported in events yet: the guest isn't asked for the clips' photos or videos. For an event, use Video Recorder or an AI Online template. (It works fine when you Process in the studio.) Flipbook templates also can't be used in Automation Studio.

Three things to remember

  1. Frames per second decides the page count.
  2. Crop keeps every frame full and steady.
  3. The numbers on the binder strip keep your pages in order.

Troubleshooting

Too many pages are printed.

Lower Frame Per Second or Record Duration (Seconds), use more frames per page in Composition, or switch Playback Mode from Boomerang to Normal.

The clip covers part of the picture.

Check that the binder side matches the side you clip, and increase the binder width.

The animation jumps or frames look different sizes.

Use Crop for Image Size, cut with a guillotine along the lines, and stack strictly by the frame numbers.

The cover does not appear.

Turn on Use cover image on the Cover Image tab; picking an image alone is not enough.

"AI-Online must produce a Video output for Flipbook."

The AI Online template you chose makes a still picture. Switch that template to a video model, or press Turn into video in it (older versions: turn on Video Chain).

"Please select or create a studio template."

Content is on Studio Template but nothing is loaded. Load a template, or switch to Video Recorder.

"Please select a custom overlay image."

Overlay is on Custom with no PNG picked.

"Please select a media input."

You pressed Run Template without picking a video or photo.

There are no numbers on the pages.

The numbers are printed in the binder strip. With Binder on None or 0 there are none.

My logo isn't on the printed frames.

Set Overlay to Custom and pick the PNG. Default only goes on the video.

An AI video made far too many pages.

Set Content › Max Video Length, for example to 5 s.

The print counter jumped by many prints.

Flipbook prints count each sheet, not each book.

There is a watermark or a DEMO badge.

The license doesn't have the Flipbook add-on (or it's a trial). Flipbook is included in Pro.

Next steps

Still need help?

Our team answers on WhatsApp. Tell us your Q-Booth version and what you see on screen.

Chat on WhatsApp